- This MPU6050 module with Triple Axis Accelerometer is based on MPU6050 chip from InvenSense. It sports a 3 Axis Accelerometer and 3 Axis Gyroscope along with an onboard Digital Motion Processor. The Digital Motion Processor is capable of processing complex 9 axis MotionFusion algorithms. The gyroscope is used to measure the rotational velocity or rate of change of angular position over time, along the X, Y and Z axis. The MPU6050 module with accelerometer uses the MEMS technology. The accelerometer measures acceleration over time. It can measure gravitational acceleration along 3 axis, using which we can calculate the angle at which sensor is positioned. So, by using, accelerometer and gyroscope data together, very accurate information on the position of the sensor can be obtained.
- Input Supply Voltage: 2.3V to 3.4V
- I2C digital output of 6 or 9 axis MotionFusion data in rotation matrix, quaternion, Euler Angle, or raw data format
- Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of ±250, ±500, ±1000, and ±2000 °/sec (dps)
- Tri-Axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
- Embedded algorithms for run-time bias and compass calibration. No user intervention required.
MPU-6050 3-Axis Accelerometer and Gyro Sensor
- Chip built-in 16bit AD converter, 16-bit data output
- Driver Chip: MPU6050
- Operating Voltage: 3-5V DC
- Communication: I2C/IIC Protocol
- Gyro Range: ± 250, 500, 1000, 2000 °/s
- Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g
₹500.00
Out of stock
Category:
Sensor
Related products
-
Read moreFeatures:-
- The LM393, use of the wide voltage comparator
- Provide both digital and analog output
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- The sensor uses the high-quality FR – 04 double material, the large area of 5.5 * 4.0 CM
- Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance
- The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 mA;
- With potentiometer sensitivity adjustment
- The output format: digital switch output (0 and 1) and analog AO voltage output;
- Has a fixed bolt hole, convenient installation
Specifications:-
- Operating Voltage (VDC) : 3.3 ~ 5
- Voltage Comparator : LM393
-
Read moreLDR Light Sensor Module LDR sensor module is used to detect the intensity of light. It is associated with both analog output pin and digital output pin labelled as AO and DO respectively on the board. When there is light, the resistance of LDR will become low according to the intensity of light. The greater…
-
Read moreThe Passive Infrared Sensor (PIR) sensor module is used for motion detection. It is often referred to used “PIR”, “Pyroelectric”, “Passive Infrared” and “IR Motion” sensor. The module has an on-board pyroelectric sensor, conditioning circuitry and a dome shaped Fresnel lens. It is used to sense movement of people, animals, or other objects. They are…
-
Add to cart- Supports momentary or latching/toggle modes.
- Supports Active High or Active Low output signal modes.
- Dimensions : 15mm x 11mm.
- Input Voltage : 2 Volt – 5.5 Volts DC.
- The response time max ~ 60mS in fast mode, ~220mS at low power mode @VDD=3V.
- Sensitivity can adjust by the capacitance(0~50pF).
- Have two kinds of sampling length by pad option(SLRFTB pin).
- Stable touching detection of the human body for replacing traditional direct switch key.
- Provides Fast mode and Low Power mode selection by pad option(LPMB pin).
- Provides direct mode、toggle mode by pad option(TOG pin).
- Open drain mode by bonding option, OPDO pin is open drain output, Q pin is CMOS output.
- All output modes can be selected active high or active low by pad option(AHLB pin).
- Have the maximum on time 100sec by pad option(MOTB pin).
- Have external power-on reset pin(RST pin).
- After power-on have about 0.5sec stable-time, during the time do not touch the keypad, and the function is disabled.
- Auto calibration.
- Re-calibration period is about 4.0 sec when the key has not be touched.